Latest Cisco CCNP Wireless 300-370 EXAM QUESTIONS [Dec-2017 Dumps]

Cisco 300-370 exam is very helpful for applicants to identify Network Engineer, Wireless Network Engineer and Wireless Network Manager. Applicants will also learn how to improve Describe stacking as it related to wireless licenses and WCM role. Applicants, who will clear this 300-370 Cisco Certified Network Professional Wireless certification exam, will receive CCNP Wireless certifications. CCNPtips provides you updated 300-370 exam questions for your 300-370 exam preparation.

300-370 Exam Questions, 300-370 PDF dumps; 300-370 exam dumps:: (60 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-370 Exam Questions:

Question: 11

Employees upgraded company issued OS devices. Which are configured to authenticate to the network using WPA2-Eniefpnse 802 lx with LEAP As a result, the devices are no longer able to authenticate Which action must the engineer do 10 resolves the issue?

Refer to the exhibit.

A. Redeploy the existing configuration profile.
B. Change LEAP certificate on the ACS server.
C. Reset the network settings on the devices.
D. Rejoin the enterprise network manually.
E. Deploy a new configuration profile with LEAP enabled

Answer: B

Question: 12

An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can be identified?
Refer to the exhibit.

A. one frequency hopping Bluetooth
B. two healthy CCK and one malformed OFDM
C. three broadband jammers
D. two strong microwave ovens and one moderate

Answer: B

Question: 13

New Updated 300-370 Exam Questions 300-370 PDF dumps 300-370 practice exam dumps:

Which statement about the join process of the access point is true?
Refer to the exhibit.

A. The time on the controller is outside of the certificates validity time interval, so the join phase failed.
B. The AP successfully joined the controller.
C. The AP moved from this controller to its primary controller.
D. The AP failed to join because the MAC address of the AP was not correct on the controller.
E. The controller rejected all discovery requests from the AP because they were not received on the management interface subnet.

Answer: E

Question: 14

A new wireless deployment with high AP density is experiencing high latency and connectivity issues on the 24 GHz band, despite an initial site survey done by a certified partner. Which option is the most impactful change a wireless consultant recommends?

Refer to the exhibit.

A. Increase the fragmentation threshold to allow larger packets over the air.
B. Reduce the beacon period because it reduces the RF interference.
C. Disable lower data rate, such as 1 Mbps and 2 Mbps.
D. Disable the short preamble.
E. Disable 80211g support to reduce interference.

Answer: C

Question: 15

A wireless user is experiencing connectivity issues with their Mac OS laptop. If the Mac is exhibiting the behavior of a “sticky client,” how can the tech verify which AP the user is currently connected to?

A. Hold shift while clicking the wireless icon.
B. Hold option while clicking the wireless icon.
C. Hold control while clicking the wireless icon.
D. Hold command while clicking the wireless icon.

Answer: B

Question: 16

You have successfully configured HA and SSO using two Cisco 5508 Wireless LAN Controllers. You are able to access the Active Primary WLC but are unable to access the Secondary Standby WLC. Which two methods will allow you to access the standby unit? (Choose two.)

A. Via SSH to the Redundancy Management Interface.
B. Via Service Port Interface.
C. Via SSH to the Management Interface.
D. Via console connection.

Answer: CD


Question: 18

An engineer has configured 802 1x for the network and all but one of the APs are passing authentication. Which configuration is causing the failure?

A. The AP has override global credentials checked.
B. The switch AAA credentials do not match what is configured on ISE.
C. The controller 802 1x supplicant credentials do not match what is configured on ISE
D. EAP-FAST is configured on ISE for this AP.

Answer: A

Question: 19

An engineer is troubleshooting AP join issues on a wireless infrastructure. While gathering debugs, the engineer notices that one of the commands may generate an excessive an excessive amount of data on the console. Which command causes this to occur?

A. debug capwap detail enable
B. debug capwap errors enable
C. debug capwap info enable
D. debug capwap events enable
E. debug capwap packet enable
F. debug capwap payload enable

Answer: B

Question: 20

Which ports require unrestricted port access for CleanAir RF spectrum analysis between the AP and Cisco Spectrum Expert?

A. UDP 5246 and 5247
B. UDP 37540 and 37550
C. TCP 16113 and 16114
D. TCP 37540 and 37550
E. TCP 5246 and 5247
F. UDP 16113and 16114

Answer: D

Question: 21

A network engineer is troubleshooting why EAP authentication with a client is failing. Which two commands should be used to resolve the issue? (Choose two)

A. debug dot1x notifications enable
B. debug dot1x events enable
C. debug arp
D. debug aaa detail enable
E. debug aaa events detail enable

Answer: BE

Question: 22

An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can the engineer identify?
Refer to the exhibit.

A. microwave
B. DECT phone
C. Bluetooth
D. jammer

Answer: A

Question: 23

An engineer is troubleshooting access point placement issues and suspects that poor placement is causing connectivity issues When running the show client detail command, the engineer notices this output Which option indicates poor access point placement?
Refer to the exhibit.

A. excessive number of bytes sent compared to bytes received
B. high signal-to-noise ratio
C. excessive number of data retries
D. low ratio signal strength indicator
E. duplicate received packets
F. poor statistics for the last 90 seconds

Answer: CD

Question: 24

An AP will be deployed to an area where DHCP Option 43 is unavailable and the WLAN engineer is unable to have DNS modifications made to support this AP. Which two actions can enable the AP to join the WLC? (Choose two)

A. Issue the clear capwap private-config command in the AP console.
B. Pre-stage or prime the AP on the same Layer 2 VLAN as the WLC.
C. Issue the capwap ap ip default-gateway WLC IP address command in the AP console.
D. Issue the capwap ap ip address WLC IP address command in the AP console.
E. Issue the capwap ap controller ip address WLC IP address command in the AP console.

Answer: AD

Facebook Comments